Белорусский национальный технический университет
Repository of the Belarusian National Technical University
ISSN: 2310-7405
Repository of the Belarusian National Technical University
View Item 
  •   Repository BNTU
  • Сериальные издания
  • Литье и металлургия
  • 2020
  • № 2
  • View Item
  •   Repository BNTU
  • Сериальные издания
  • Литье и металлургия
  • 2020
  • № 2
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Влияние термической обработки на структурно-фазовое состояние и дюрометрические свойства малоразмерных отливок из медного сплава Cu-Cr-Al

Thumbnail
DOI
10.21122/1683-6065-2020-2-22-25
Authors
Марукович, Е. И.
Кукареко, В. А.
Харьков, В. А.
Кушнеров, А. В.
Сазоненко, И. О.
Date
2020
Publisher
БНТУ
Another Title
The influence of heat treatment on the structural phase state and durometric properties of small-sized castings from a copper alloy Cu-Cr-Al
Bibliographic entry
Влияние термической обработки на структурно-фазовое состояние и дюрометрические свойства малоразмерных отливок из медного сплава Cu-Cr-Al = The influence of heat treatment on the structural phase state and durometric properties of small-sized castings from a copper alloy Cu-Cr-Al / Е. И. Марукович [и др.] // Литье и металлургия. – 2020. – № 2. – С. 22-25.
Abstract
В работе исследовано влияние термической обработки на структурно-фазовое состояние и твердость малоразмерных отливок из медного сплава Cu-Cr-Al, полученных литьем в водоохлаждаемый металлический кокиль. Методом рентгеноструктурного анализа установлено, что отливки состоят из матричного твердого раствора на основе меди. Повышенное значение параметра кристаллической решетки медной фазы связано с растворенными в ней атомами алюминия. После низкотемпературного (450 °C) отпуска в течение 10 ч параметр кристаллической решетки матричного твердого раствора уменьшается, что связано с образованием на поверхности отливки интерметаллида Al8Cr5. Установлено, что после термической обработки (закалки и отпуска) твердость отливок из сплава Cu-Cr-Al увеличивается в 1,5 раза.
Abstract in another language
The effect of heat treatment on the structural-phase state and hardness of small-sized castings made from the Cu-Cr-Al copper alloy obtained by casting in a water-cooled metal mold is studied. Using X-ray diffraction analysis, it was found that the castings consist of a matrix solid solution based on copper. The increased value of the crystal lattice parameter of the copper phase is associated with aluminum atoms dissolved in it. After a low-temperature (450 °C) tempering for 10 hours, the crystal lattice parameter of the matrix solid solution decreases, which is associated with the formation of the Al8Cr5 intermetallic compound on the surface of the casting. It is established that after heat treatment (hardening and tempering), the hardness of castings from the Cu-Cr-Al alloy increases by 1.5 times.
URI
https://rep.bntu.by/handle/data/73617
View/Open
Статья (426.4Kb)
Collections
  • № 2[16]
Show full item record
CORE Recommender

Belarusian National Technical University | Science Library | About Repository | Размещение в Репозитории | Contact Us
Яндекс.МетрикаIP Geolocation by DB-IP
Science Library | About Repository | Размещение в Репозитории | Contact Us
 

Browse

All of Repository BNTUCommunities & CollectionsAuthorsTitlesBy Issue DatePublisherBy Submit DateTypeThis CollectionAuthorsTitlesBy Issue DatePublisherBy Submit DateType

My Account

LoginRegister

Belarusian National Technical University | Science Library | About Repository | Размещение в Репозитории | Contact Us
Яндекс.МетрикаIP Geolocation by DB-IP
Science Library | About Repository | Размещение в Репозитории | Contact Us