Белорусский национальный технический университет
Repository of the Belarusian National Technical University
ISSN: 2310-7405
Repository of the Belarusian National Technical University
View Item 
  •   Repository BNTU
  • Сериальные издания
  • Литье и металлургия
  • 2025
  • № 3
  • View Item
  •   Repository BNTU
  • Сериальные издания
  • Литье и металлургия
  • 2025
  • № 3
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Оценка неравномерности пластической деформации при волочении высокопрочной проволоки из перлитной стали

Thumbnail
DOI
10.21122/1683-6065-2025-3-56-60
Authors
Фетисов, В. П.
Date
2025
Publisher
БНТУ
Another Title
Assessment of the unevenness of plastic deformation in drawing high-strength pearlite steel wire
Bibliographic entry
Фетисов, В. П. Оценка неравномерности пластической деформации при волочении высокопрочной проволоки из перлитной стали = Assessment of the unevenness of plastic deformation in drawing high-strength pearlite steel wire / В. П. Фетисов // Литье и металлургия. - 2025. - № 3. - С. 56-60.
Abstract
Контролем пластических свойств проведено сравнение надежности предварительной оценки неравномерности пластической деформации в процессе многократного волочения высокопрочной проволоки с помощью расчетного геометрического параметра клиновидной зоны и экспериментально определяемого подъема металла на входе в рабочий конус волоки. Геометрический параметр клиновидной зоны не характеризует влияние на формирование пластических свойств повышения прочности, соотношения сжимающих и растягивающих напряжений в очаге деформации при изменении единичного обжатия и поэтому не может применяться в качестве показателя неравномерности пластической деформации при многократном волочении высокопрочной проволоки из перлитной стали. Определяемый при волочении на разъемных волоках подъем металла на входе в деформационную зону волочильного инструмента обладает повышенной чувствительностью к изменению основных технологических параметров процесса волочения и соответствует критерию неравномерности пластической деформации высокопрочной стали. С увеличением суммарного обжатия при волочении высокопрочной проволоки дополнительной оценкой неравномерности пластической деформации является соотношение сжимающих и растягивающих напряжений в схеме объемного напряженного состояния. Для повышения равномерности деформации при многократном волочении высокопрочной проволоки необходимо снижение единичных обжатий и уменьшение угла рабочего конуса волоки по мере роста суммарной степени деформирования. Деформацию волочением следует осуществлять с противонатяжением и в режиме гидродинамического трения.
Abstract in another language
Under the control of plastic properties, the reliability of a preliminary assessment of the unevenness of plastic deformation during repeated drawing of high‑strength wire was compared using the calculated geometric parameter of the wedge‑shaped zone and the experimentally determined metal lift at the entrance to the working cone of the drawing. The geometric parameter of the wedge‑shaped zone does not characterize the effect on the formation of plastic properties of increased strength, the ratio of compressive and tensile stresses in the deformation zone with a change in a single compression, and therefore cannot be used as an indicator of the unevenness of plastic deformation during repeated drawing of high‑strength wire made of pearlite steel. The rise of metal at the entrance to the deformation zone of the drawing tool, determined by drawing on split lugs, is highly sensitive to changes in the main technological parameters of the drawing process and meets the criterion of uneven plastic deformation. To increase the uniformity of deformation during repeated drawing of high‑strength wire, it is necessary to reduce single compressions and reduce the angle of the working cone of the drawing as the total degree of deformation increases, as well as to carry out deformation by drawing with counter‑tension and in the mode of hydrodynamic friction.
URI
https://rep.bntu.by/handle/data/158816
View/Open
56-60.pdf (341.8Kb)
Collections
  • № 3[2]
Show full item record
CORE Recommender

Belarusian National Technical University | Science Library | About Repository | Размещение в Репозитории | Contact Us
Яндекс.МетрикаIP Geolocation by DB-IP
Science Library | About Repository | Размещение в Репозитории | Contact Us
 

Browse

All of Repository BNTUCommunities & CollectionsAuthorsTitlesBy Issue DatePublisherBy Submit DateTypeThis CollectionAuthorsTitlesBy Issue DatePublisherBy Submit DateType

My Account

LoginRegister

Belarusian National Technical University | Science Library | About Repository | Размещение в Репозитории | Contact Us
Яндекс.МетрикаIP Geolocation by DB-IP
Science Library | About Repository | Размещение в Репозитории | Contact Us