Белорусский национальный технический университет
Repository of the Belarusian National Technical University
ISSN: 2310-7405
Repository of the Belarusian National Technical University
View Item 
  •   Repository BNTU
  • Материалы конференций и семинаров
  • Международные и республиканские конференции
  • Приборостроение
  • Приборостроение-2023
  • Материалы конференции по статьям
  • View Item
  •   Repository BNTU
  • Материалы конференций и семинаров
  • Международные и республиканские конференции
  • Приборостроение
  • Приборостроение-2023
  • Материалы конференции по статьям
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Влияние длины образцов на величину остаточной намагниченности после импульсного намагничивания накладным датчиком

Thumbnail
Authors
Бурак, В. А.
Коваленок, И. А.
Протасевич, А. С.
Date
2023
Publisher
БНТУ
Another Title
The influence of sample length on the residual magnetization after pulse magnetization with an attached sensor
Bibliographic entry
Бурак, В. А. Влияние длины образцов на величину остаточной намагниченности после импульсного намагничивания накладным датчиком = The influence of sample length on the residual magnetization after pulse magnetization with an attached sensor / В. А. Бурак, И. А. Коваленок, А. С. Протасевич // Приборостроение-2023 : материалы 16-й Международной научно-технической конференции, 15-17 ноября 2023 года, Минск, Республика Беларусь / редкол.: О. К. Гусев (пред.) [и др.]. – Минск : БНТУ, 2023. – С. 205-206.
Abstract
В данной работе рассмотрено влияние на величину остаточной намагниченности длины образцов из инструментальных углеродистых марок сталей и расположения импульсного намагничивания и датчика на поверхности цилиндрического образца. Установлено, что для стали, закаленной от температуры выше рекомендуемой, при расположении датчика на торце образца, существует значение длины, при повышении которой величина градиента нормальной составляющей напряженности поля остаточной намагниченности стабилизируется. Были даны практические рекомендации по определению оптимального положения датчика на поверхности цилиндрического образца с целью повышения надежности и достоверности импульсного магнитного неразрушающего контроля.
Abstract in another language
This work is considered the effect on the value of residual magnetization of the length of samples made of tool carbon steel and the location of pulse magnetization and a sensor on the surface of a cylindrical sample on the value of residual magnetization. It has been established that for steel hardened at a temperature higher than recommended one, when the sensor is located at the end of the sample, there is a length value increasing of which results to stabilization of the magnitude of the gradient of the normal component of the residual magnetization field strength. Practical recommendations were given for determining the optimal position of the sensor on the surface of a cylindrical sample in order to increase the reliability of pulsed magnetic non-destructive testing.
URI
https://rep.bntu.by/handle/data/138486
View/Open
205-206.pdf (314.5Kb)
Collections
  • Материалы конференции по статьям[224]
Show full item record
CORE Recommender

Belarusian National Technical University | Science Library | About Repository | Размещение в Репозитории | Contact Us
Яндекс.МетрикаIP Geolocation by DB-IP
Science Library | About Repository | Размещение в Репозитории | Contact Us
 

Browse

All of Repository BNTUCommunities & CollectionsAuthorsTitlesBy Issue DatePublisherBy Submit DateTypeThis CollectionAuthorsTitlesBy Issue DatePublisherBy Submit DateType

My Account

LoginRegister

Belarusian National Technical University | Science Library | About Repository | Размещение в Репозитории | Contact Us
Яндекс.МетрикаIP Geolocation by DB-IP
Science Library | About Repository | Размещение в Репозитории | Contact Us