Белорусский национальный технический университет
Repository of the Belarusian National Technical University
ISSN: 2310-7405
Repository of the Belarusian National Technical University
View Item 
  •   Repository BNTU
  • Материалы конференций и семинаров
  • Международные и республиканские конференции
  • Приборостроение
  • Приборостроение-2021
  • Материалы конференции по статьям
  • View Item
  •   Repository BNTU
  • Материалы конференций и семинаров
  • Международные и республиканские конференции
  • Приборостроение
  • Приборостроение-2021
  • Материалы конференции по статьям
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Влияние толщины изделий при изучении процессов деформации стали 12Х18Н10Т с помощью магнитодинамического метода контроля

Thumbnail
Authors
Шарандо, В. И.
Чернышёв, А. В.
Кременькова, Н. В.
Полоневич, А. А.
Date
2021
Publisher
БНТУ
Another Title
Influence of the thickness of products in studying the processes of deformation of steel 12Х18Н10Т using the magnetodynamic
Bibliographic entry
Влияние толщины изделий при изучении процессов деформации стали 12Х18Н10Т с помощью магнитодинамического метода контроля = Influence of the thickness of products in studying the processes of deformation of steel 12Х18Н10Т using the magnetodynamic / В. И. Шарандо [и др.] // Приборостроение-2021 : материалы 14-й Международной научно-технической конференции, 17-19 ноября 2021 года, Минск, Республика Беларусь / редкол.: О. К. Гусев (председатель) [и др.]. – Минск : БНТУ, 2021. – С. 371-372.
Abstract
Исследовано изменение величины магнитного потока, измеряемого магнитным толщиномером МТЦ-3, и остаточной намагниченности, измеряемой измерителем остаточной намагниченности ИОН-4, от степени пластической деформации и толщины образцов из аустенитной стали 12Х18Н10Т. Установлено, что максимальная толщина, с достижением которой прекращается изменение сигналов обоих магнитодинамических приборов, составляет 3–4 мм. С увеличением степени деформации и толщины образца показания прибора МТЦ-3 возрастают. Показания прибора ИОН-4 имеют максимум в области деформаций 15–25%, положение и высота которого определяются толщиной образца.
Abstract in another language
The change in the magnitude of the magnetic flux, measured by the magnetic thickness gauge MTTs-3, and the remanent magnetization, measured by the meter of remanent magnetization ION-4, on the degree of plastic deformation and the thickness of the samples of austenitic steel 12X18H10T, was investigated. It was found that the maximum thickness, upon reaching which the change in the signals of both magnetodynamic devices stops, is 3–4 mm. With the increasing in the degree of deformation and thickness of the sample, the readings of the MTTs-3 device increase. The readings of the ION-4 device have a maximum in the range of deformations of 15–25%, the position and height of which are determined by the thickness of the sample.
URI
https://rep.bntu.by/handle/data/109588
View/Open
371-372.pdf (325.7Kb)
Collections
  • Материалы конференции по статьям[230]
Show full item record
CORE Recommender

Belarusian National Technical University | Science Library | About Repository | Размещение в Репозитории | Contact Us
Яндекс.МетрикаIP Geolocation by DB-IP
Science Library | About Repository | Размещение в Репозитории | Contact Us
 

Browse

All of Repository BNTUCommunities & CollectionsAuthorsTitlesBy Issue DatePublisherBy Submit DateTypeThis CollectionAuthorsTitlesBy Issue DatePublisherBy Submit DateType

My Account

LoginRegister

Belarusian National Technical University | Science Library | About Repository | Размещение в Репозитории | Contact Us
Яндекс.МетрикаIP Geolocation by DB-IP
Science Library | About Repository | Размещение в Репозитории | Contact Us