Show simple item record

dc.contributor.authorШелег, В. К.
dc.contributor.authorМинь, Ма
dc.contributor.authorБелоцерковский, М. А.
dc.coverage.spatialМинскru
dc.date.accessioned2021-10-06T11:56:31Z
dc.date.available2021-10-06T11:56:31Z
dc.date.issued2021
dc.identifier.citationШелег, В. К. Технология получения и демпфирующие свойства аэрированных полимерных покрытий = Production Technology and Damping Properties of Aerated Polymer Coatings / В. К. Шелег, Ма Минь, М. А. Белоцерковский // Наука и техника. – 2021. – № 5. – С. 375-382.ru
dc.identifier.urihttps://rep.bntu.by/handle/data/103439
dc.description.abstractРазработан и исследован процесс получения аэрированных (наполненных пузырьками воздуха) полимерных покрытий методом газопламенного напыления с оценкой их способности к демпфированию колебаний. Используя возможности конструкции полимерного термораспылителя модели ОИМ 050, заключающиеся в обеспечении подачи спутного воздушного потока между факелом пламени и струей порошкового материала, разработана технология управляемого формирования аэрированных полимерных покрытий. Эксперименты выполнялись с такими термопластичными полимерами, как полиэтилентерефталат, полиэтилен высокого давления, сверхвысокомолекулярный полиэтилен, полиамид. Установлено, что коэффициент аэрирования растет практически прямо пропорционально с увеличением количества воздуха в спутном потоке у всех исследуемых полимерных покрытий. Отмечено, что на процесс аэрирования оказывают влияние реологические свойства жидких полимеров, а точнее, величина показателя текучести расплава полимера. Определены предельные значения воздуха в спутном потоке, которые позволяют не снижать значения адгезии полимерных покрытий со стальными подложками менее 6 МПа и не уменьшать их твердость более чем на 25–30 %. Исследования демпфирующих свойств образцов с полимерными покрытиями осуществляли на стенде, кинематическая схема которого основана на нагружении свободного конца консольно закрепленного образца, резком снятии нагрузки и регистрации свободных затухающих колебаний бесконтактным датчиком индукционного типа, связанным с компьютером. Показано, что использование аэрирования при формировании шумопоглощающих покрытий на стальных образцах позволяет увеличить их логарифмический декремент затухания на 18–26 %.ru
dc.language.isoruru
dc.publisherБНТУru
dc.titleТехнология получения и демпфирующие свойства аэрированных полимерных покрытийru
dc.title.alternativeProduction Technology and Damping Properties of Aerated Polymer Coatingsru
dc.typeArticleru
dc.identifier.doi10.21122/2227-1031-2021-20-5-375-382
local.description.annotationThe process of obtaining aerated (filled with air bubbles) polymer coatings has been developed and investigated by the method of flame spraying with an assessment of their ability to damp vibrations. A technology for the controlled formation of aerated polymer coatings has been developed while using the capabilities of the ОИМ (OIM) 050 polymer thermal atomizer design which consists in providing a concurrent air flow between the flame torch and the jet of powder material. The experiments have been carried out with such thermoplastic polymers as polyethylene terephthalate, high pressure polyethylene, ultra high molecular weight polyethylene, polyamide. It has been found that the aeration coefficient grows almost in direct proportion with an increase in the amount of air in the concurrent flow for all investigated polymer coatings. It is noted that the aeration process is influenced by the rheological properties of liquid polymers, or rather, the value of the polymer melt flow rate. The limiting values of air in the concurrent flow have been determined, which make it possible not to reduce the adhesion of polymer coatings to steel substrates by less than 6 MPa and not to decrease their hardness by more than 25–30 %. Studies of the damping properties of samples with polymer coatings have been carried out on a stand, the kinematic diagram of which is based on loading the free end of a cantilever sample, abrupt removal of the load and registration of free damped oscillations by an induction-type contactless sensor connected to a computer. It is shown that the use of aeration when forming noise-absorbing coatings on steel samples can increase their logarithmic damping decrement by 18–26 %.ru


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record